青年中文yield strength的意思
yield strength中文翻譯：
屈變力，屈服強度，抗屈強度
[力]屈服強度；屈變力；抗屈強度
相似詞語短語
yield strengths───[力]屈服強度；屈變力；抗屈強度
field strength───[物][電子]場強；電場強度；磁場強度
field strengths───[物][電子]場強；電場強度；磁場強度
find strength───找到力量
full strength───滿員；全強度
great strength───牛勁；強大的力量
green strength───[材]濕強度；生坯強度
in strength───大量地
real strength───實際強度
雙語使用場景
Residual stress concentration a notch depends on both notch geometry and yield strength of the material.───缺口根部的殘余應力存在應力集中效應,應力集中值不僅取決于缺口幾何形狀而且和材料的屈服強度有關.
Oxgen precipitates ( useful for gettering ) can reduce the yield strength ( critical shear stress ) up to fivefole.───氧沉淀 ( 可用作吸雜 ) 會使屈服強度 ( 臨界剪應力 ) 降低為五分之一.
Fatigue strength is less than static stress strength such as elasticity limit, yield strength.───疲勞強度低于彈性極限或屈服強度等靜應力強度。
CuPTiRE anti - erosion hot rolling stripes are divided into two grades in yield strength : 295 MPa, 345 MPa.───09CuPTiRE耐大氣腐蝕熱軋鋼板按屈服強度分為295MPa級和345MPa級兩個級別.
The V - N microalloy steel with yield strength of 550 MPa is produced by EAF - CSP route.───目前,在EAF-CSP 流程中通過V -N 微合金化技術可成功生產屈服強度為550MPa的高強度低合金鋼.
Good yield strength and tensile strength.───良好的屈服強度和抗拉強度。
FIG. 5 shows the average yield strength as a function of extrusion speed and location.───圖5示出了平均屈服強度與擠壓速度和位置的關系.
Dislocation strengthening and grain refinement strengthening makes coil 059 with the higher yield strength.───位錯強化與晶粒細化強化是059板卷具有高屈服強度的原因.
The yield strength fy of reinforcement is used in design.───在設計中利用的是鋼筋的屈服強度.
Yield strength elongation-strain corresponding to yield strength of material.───屈服強度伸長—對應于材料屈服強度的應變。
The yield strength ( σ0.2 ) , ultimate tensile strength ( σ b ) and elongation ( δ ) of A 356 - T 6 alloy were 240 MPa, 254.8 MPa and 1.16 % , respectively.───屈服強度 、 抗拉強度和伸長率分別為240MPa 、 254.8MPa和1.16%.
The creep rate was increased while the yield strength was reduced by anodic dissolution.───陽極電流不但使恒載荷下的不銹鋼蠕變速度增加,而且使屈服強度下降.
The yield strength, tensile ratio and toughness are major quality indexes of steel pipe ( board ).───屈服強度 、 屈強比、韌性等是鋼管 ( 板 ) 的主要質量指標,合理確定這些指標的數值有相當難度.
The results show that the steel has high yield strength and quality forming property.───結果表明,研制開發出的鈮鈦微合金化IF鋼具有高的屈服強度和優良的成形性能.
Desirable properties for forming include low yield strength and high ductility.───令人滿意的成形特性包含了低降伏應力和高延展性.