青年中文centrifugal casting的意思
centrifugal casting中文翻譯：
[機]離心澆鑄
離心澆鑄造法
相似詞語短語
centrifugal castings───[機]離心澆鑄
central casting───(電影制片廠的)演員選派部，電影廠分派次要角色的部門
centrifugalising───離心
central castings───(電影制片廠的)演員選派部，電影廠分派次要角色的部門
centrifugal clutch───[機][車輛]離心式離合器
centrifugalization───n.離心分離作用；利用離心機而分離的物質
centrifugalizing───vt.使受離心作用
centrifugal clutches───[機][車輛]離心式離合器
continuous casting───全連鑄；[冶]連續澆鑄
雙語使用場景
Widely used for winding Al ( Cu, Steel ) foil. These rollers are produced by centrifugal casting methods.───箔材芯管套筒廣泛應用于軋制鋁 ( 銅 、 鋼等 ),套筒采用離心鑄造工藝生產.
A method of dynamic action was used during the solidification of the alloy in centrifugal casting.───在離心澆鑄金屬凝固過程中,采用動態效應的方法對以達到細化晶粒的目的.
Centrifugal casting, compact structure, free from pinhole porosity and slag, smooth surface and even wall thickness.───高速離心鑄造, 組織致密, 無砂眼、夾渣, 表面光滑、壁厚均勻.
Technology of vertical centrifugal casting, the calculation for gate size and rotational speed mold were introduced.───介紹了立式離心鑄造方法 、 澆口尺寸和鑄型轉速的計算.
Although there are a lot of the fabricating techniques of functionally gradient material (FGM), the centrifugal casting method is more effective, cheaper and easier to operate.───雖然梯度功能材料的制備方法很多，但效率較高、成本較低、操作較簡單的方法是離心鑄造法。
Technology for shaped castings in vertical centrifugal casting, including design principle and technology parameters, is described.───敘述了異型鑄件立式離心鑄造的工藝, 其中包括設計原則和工藝參數.
The centrifugal casting process of high aluminum - zinc alloys was investigated through products.───結合產品試驗了高鋁鋅基合金的離心鑄造工藝.
The development process and status, and further research directions of FGMs by centrifugal casting are comprehensively discussed in this paper.───本文對離心鑄造法制備梯度功能材料的發展過程、研究現狀及今后研究的方向進行了綜合評述。
The effects of mischmetal addition on the microstructure in centrifugal casting lead bronze hare been studied.───研究了混合稀土對離心鑄造鉛青銅組織的影響.
Based on rapid prototyping technology the silicon rubber mold for centrifugal casting is conveniently made.───硅橡膠模離心澆注裝置結構簡單,投資少.
These rolls can be produced by static casting or centrifugal casting.───可采用靜態鑄造或離心鑄造生產.
A new type of centrifugal casting coating was introduced and its relative performances were tested.───介紹了一種新的離心鑄造用涂料的配制,測定了其有關性能.
The corresponding measures should be adopted on raw material management, hot metal melting and centrifugal casting.───相應的應從原材料管理, 鐵水熔煉,離心鑄造上采取控制措施.
A number of practical patent coatings for centrifugal casting pipe are listed in this paper.───文中列出大量實用的離心鑄管涂料專利配方.
unsaturated polyester resin is designed for centrifugal casting molding glass pipe (HOBAS pipe) design of the structure layer resin is a low viscosity, medium reactivity of o-benzene resin.───不飽和聚酯樹脂是專門為離心澆鑄成型玻璃鋼管道(HOBAS管)設計的結構層樹脂，是低粘度，中等反應性的鄰苯型樹脂。
英語使用場景
The two motor driving rollers of the centrifugal casting machine must keep synchronous and keep load balance.
The Electromagnetic levitation melt centrifugal casting(ELCC)technology for preparing the low cost high quality silicon solar cell paves a new way for reducing the production cost of the solar cell.
This paper introduced that horizontal centrifugal casting technology is used to develop the composite acicular spheroidal graphite cast iron collar for tension reducing mill of Baogang pipe mill.
One of keys of production of centrifugal casting pipe of s. g. iron is continuous and fast delivery of qualified base iron with proper chemical composition and temperature.
The technology of grinding ball by centrifugal casting, the rotational speed, the method for calculation of ingate area and factors influencing technological process were introduced.
The shortcomings of horizontal centrifugal casting machine are analyzed, and a vertical casting unit in structure of double-layered hollow abdomen is designed.
The influence of rotating speed of centrifugal casting machine on the semi-solid microstructure of Al-Si alloy was researched.
In the light of application to centrifugal casting machine, working principle of soft starter is analyzed and the advantage of this new energy-saving technique of soft starter is presented.
Some aspects in cast-iron drainpipe production in centrifugal casting, such as machine type, influence of coating, formation of pit and pin-hole defects, were analyzed and approached.