roll bending的意思

roll bending中文翻譯：

[機]軋輥撓度；滾筒彎曲加工

相似詞語短語

bending───n.彎曲，彎曲度；v.彎曲（bend的現在分詞）

flatwise bending───平面彎曲

bending over───俯身；折轉

flexural bending───塑性彎曲

anticlastic bending───抗塑性彎曲

bending moment───[力]彎矩；[力]彎曲力矩；[力]撓矩；彎（曲）矩，撓矩

roll───n.(Roll)（美、挪、加）羅爾（人名）；v.滾動；翻身；（眼睛）轉動；在原地打滾；（馬）仰臥蹬腳；左右搖晃；蹣跚；使翻車；擲（骰子）；擲出（骰子數）；（轉動）肩膀；行駛；推；搖車窗；（液體）滾落；（時間）流逝；穩定持續的；（產品）從（機器）產出；涌流；延綿起伏；運轉；卷，卷起；展開；搓成；輾；發出隆隆聲；把（衣服的邊）卷起來；壓平；覆蓋；啟動；用顫音發出（輔音，尤其是r）；n.卷；柱形物；卷狀食品；滾動；翻筋斗；左右搖晃；隆隆聲；小面包；總人數；名單；公文；延綿起伏；輥軋機；一管；擲骰子

mutton roll───羊肉卷

french roll───法國式小面包；法式小面包；單面印刷卷筒紙

雙語使用場景

Avoid high stress concentrations at the ends of the work roll barrel. Ensure good control of roll bending.───避免在工作輥輥端部位應力過于集中。確保彎輥得到很好的控制。

work principle and technical advantages of two-axle roll bending with elastic medium(RSEM) are described.───介紹了兩軸柔性滾彎的工作原理和技術優勢。

Nearly all rolling mills are fitted with work roll bending equipment.───幾乎所有的軋機均安裝了工作輥彎曲裝置。

Realization of three models, including roll-bending feedforward, crown feedback and flatness feedback, on field was described in detail.───本文詳細闡述了彎輥力前饋、凸度反饋和平坦度反饋三個模型在現場的具體實現。

The work principle and technical advantages of two-axle roll bending with elastic medium(RSEM) are described.───介紹了兩軸柔性滾彎的工作原理和技術優勢。

roller excircle rugged roll bending straight, " " marks caused by the location of the usual bite.───不朱輥外圓高低不服輥芯筆屈不屈，引起“條痕”的場所凡是在咬口處。

Improvement of the Roll Shape and Reduction of the Roll Bending Force for Increment of Life of the Work Roll Bearing and Roller───改善輥型降低彎輥力提高工作輥軸承及軋輥使用壽命

Calculation and Determination Method for Empirical Setting Parameters of Three- roll Bending- plate Internally- supporting Welded Pipe Mill───三輥彎板內承式機組經驗調型參數計算及確定方法

Calculating of the Cold-rolled Forming Section Trough Steel during Roll Bending Formation Course───冷彎型鋼槽型鋼輥彎成型過程計算

英語使用場景

The change of strip crown is in direct proportion with work roll shifting distances and roll bending force and the square of strip width.

Special Mill Features : Hydraulic Automatic Gauge Control. Positie and Negatie Work Roll Bending. Intermediate Roll Shifting.

An independent module of work roll bending compensation is set in the feedback control system.