sintering temperature的意思

sintering temperature中文翻譯：

燒結溫度；軟化溫度

相似詞語短語

temperature───n.溫度；體溫；氣溫；發燒

critical temperature───[物][電子]臨界溫度；n.臨界溫度

temperature outside───室外溫度

temperature rise───[電]溫升；溫度上升；溫度上升，溫升，升溫

constant temperature───[熱]恒溫；定溫；等溫；等溫，恒溫

fluctuating temperature───波動溫度；脈動溫度；脈動溫度，波動溫度

low temperature───低溫，低溫度；[物]低溫

annealing temperature───[機]退火溫度；退火點；退火點，退火溫度

cpu temperature───cpu溫度

雙語使用場景

Effect of sintering temperature and sintering holding time on green density was analyzed.───了燒結溫度和燒結保溫時間對壓坯密度的影響。

effect of sintering temperature on the anode porosity was investigated.───研究了燒結溫度對陽極孔隙度的影響。

sintering shrinkage increased with increasing sintering temperature.───燒結溫度的升高提高了燒結收縮率。

If sintering temperature could be decreased and materials consumption be reduced, life time of sintering equipment can be extended.───如果能夠降低燒結溫度，降低物耗，就能夠提高燒結設備的使用壽命。

Pore diameter increases with the increase of the sintering temperature , which leads to a decrease in rejection rate.───孔徑隨著燒結溫度的升高而增大，從而導致截留性能的下降；

Second, structure, morphology and electrochemical properties of the sample are closely linked with the sintering temperature.───其次，樣品的結構、形貌和電化學性能都和煅燒溫度有著緊密聯系。

It has been found that the colour of red iron oxides in ceramics is affected by sintering temperature and the compositions of the ceramics.───本文考察了燒成溫度、陶瓷坯體中常見氧化物，以及二氧化硅包裹對鐵紅呈色穩定性的影響。

The sintering behavior of powder and dependence of the density on sintering temperature and time have been studied.───研究了粉末的燒結特性，測定了燒結密度隨燒結溫度及燒結時間的變化。

Microstructure determined by both sintering temperature and high temperature holding time would influence acid corrosion resistance.───研究表明陶瓷燒結溫度和保溫時間均對陶瓷的顯微結構有影響，進而影響陶瓷的耐酸腐蝕性能。

英語使用場景

The result shows that the sintering temperature of ceramic body is reduced, but the toughness is improved obviously on substitution of nepheline for feldspar.

And sintering temperature has an important effect on the initial permeability of Mn-Zn ferrites.

The optimal sintering temperature of SrTiO3 doped with different substances was investigated based on DIL analysis. Density of samples was measured by the Archimedes principle.

High sintering temperature and long maintaining time lead to the sufficient crystallization and the full densification, but result in the worsening of the deviation from the stoichiometry.

The sintering temperature and thermal expansion coefficient of the LSGM sample were determined using dilatometer.

The effects of sintering temperature, sintering time, sintering pressure and the magnitude of orientation magnetic field on the properties of the barium ferrite thick films were studied.

With the increase of sintering temperature, the apparent porosity of sample decreases, while bulk density, hardness and compressive strength increased.

Sintering temperature influenced hot-pressing process.

The high sintering temperature and machining cost are the two key obstacles to enlarge zirconia toughening ceramics as dental prosthetic.