winding process的意思

winding process中文翻譯：

繞制法

相似詞語短語

winding───adj.蜿蜒曲折的；v.蜿蜒而行；纏繞；卷繞；被彎曲；環繞（核心）；給（鐘表等）上發條；轉動（鑰匙、把手）；（使）（錄像帶、錄音帶等）倒退（或前進）；（用絞車等）吊起（某物）；（使）氣急；輕拍后背使（嬰兒）打嗝；嗅出（人或動物的）氣味；（詩、文）吹（號角）（wind的現在分詞）；n.卷繞；線圈；蜿蜒曲折的路徑；n.(Winding)（美）溫丁（人名）

winding river───（美）風河系統公司；溫德河（美國懷俄明州河流）

armature winding───[電]電樞繞組

winding stairs───螺旋式樓梯

winding trip───繞組跳閘

winding trail───蜿蜒的小徑

winding up───清算；停業清理；清理; 結業

winding road───連續彎路；彎曲路

filament winding───纖維纏繞；燈絲繞阻；[電子]燈絲電源繞組

雙語使用場景

tension control is the key technique in the filament winding process to guarantee the product quality.───纖維纏繞中張力的控制是關系到產品質量的關鍵技術。

This UP resin is a high performance and chemical resistant resin which is suitable for winding process.───該樹脂為優良的耐化學樹脂，并適合纏繞成型的工藝要求。

mould, gel coat formulation and winding process of high performance FRP electric insulating tube were summarized.───本文介紹了玻璃鋼高強電絕緣管的模具、膠液配制及纏繞成型工藝。

and the micromotor is also provided with an independent control unit, and can independently control the whole wire winding process.───微電機還設置有獨立的控制單元，可以單獨控制整個繞線過程。

Clearing yarn parameter should be set rationally in winding process.───絡筒合理設定清紗參數；

In the literature, this impact of there winding process on stray load loss has never before been reported.───在該文獻中指出，重繞工藝對漏磁負載的影響（沖擊），以前從來沒報道過。

The stable negative-pressure system can effectively grab the yarn to make the winding process running properly.───恒定的吸風負壓使紗線能夠有效地被吸附，使絡筒工序能夠平穩地進行。

A non-contact dynamic measurement of the yarn tension in winding process based on the image process technology is proposed.───為了實現卷繞機上紗線張力非接觸式動態檢測，提出一種基于圖像處理技術的檢測方法。

It is discussed how to avoid the deviation in examination and how to adjust the spinning and winding process by the examination result.───探討了在檢驗過程中如何避免偏差，利用檢驗結果來調整優化紡絲及卷繞工藝。

英語使用場景

This product is used primarily for hand lay - up , pultrusion, RTM, and filament winding process, etc.

This paper introduces the method of fabrication of FRP nose radome by filament winding process.

Filament winding process is well suited to the manufacture of rotationally - symmetric components.

The method of design high frequency transformer in fly-back circuit in introduced in detail, besides the Transformer winding process is discussed.

The three most commonly used method of manufacturing FRP are Cross-winding process, continuous winding process and the centrifugal casting process.

According to filament winding process, a composite flywheel rotor laminated winding process was approved.