青年中文青年中文

butt weld的意思

butt weld中文翻譯:

對接焊縫;對頭焊接

相似詞語短語

unfitness of butt weld───焊縫對口錯邊量

butt───n.(Butt)人名;(英)巴特;(俄、德、印、巴基)布特;n.屁股;煙頭;笑柄;靶垛;粗大的一端;vt.以頭抵撞;碰撞

fillet weld───角焊縫,填角焊,貼角焊

butt out───別管閑事;不必多嘴

autogenous weld───氣焊

weld together───焊接在一起

butt plug───肛門插

gouged weld───福利

weld wheels───焊接車輪

雙語使用場景

Weld the outer side member with a full butt weld under shielding gas.───用氣體保護全對接焊,焊接外側梁。

weld can be divided into four types: butt weld, fillet weld, plug weld and end weld.───焊縫可分為對接焊縫、角焊縫、塞焊縫和端接焊縫四種。

fatigue resistance of the scarf weld in the end of the vessel is stronger than that of the butt weld.───部斜面焊縫結構的抗疲勞強度比對接焊縫結構高,且不會發生一次性脆性破壞;

Check whether the butt weld is smooth; there is any mismatch, or any other weld problem.───目視檢查焊接處是否平整,兩邊是否有錯位。以及是否有虛焊、焊脫現象。

The assembly deviation butt weld of has line on the part of the middle, the light is different on the sides of linear.───組對偏差的對接焊縫其焊縫偏中間區域會出現線條,線條兩側的亮度不同;

By the analysis and measures above, it improves the test quality of the process piping butt weld effectively.───通過以上分析和采取的措施,能有效提高工藝管道對接焊縫超聲波檢測的質量。

Reducing long radius butt weld elbows shall be kept to a minimum.───應盡量少用長徑異徑對焊彎頭。

Dimensions - End-to-end dimensions for butt weld , two-way, globe- type, straight pattern control valves.───尺寸。對接焊接,兩向,球型,垂直模式控制閥的末端對末端尺寸。

The other size and end connection - butt weld, socket weld and thread are available upon request.───其它尺寸及接口型式-承插焊,套焊及螺紋等可接受訂購

英語使用場景

This article introduced the experiment of residual stress in flat tubeplate head of large scale fuel boiler that was manufactured by cold rotary extruding and butt weld.

Buckling of thin plate due to butt weld was investigated using inherent strain method as an equivalent load.

Manganese burn - off from the wire in welding a single - V butt weld was studied.

Temperature and residual stress field of industrial pipe butt weld was simulated by ABAQUS codes.

This indicated that the fracture had initiated at the unfused butt weld in the longitudinal stiffener.

Buckling of thin to butt weld was investigated using inherent strain method as an equivalent load.

Butt weld and flanged valves have the same end - to - end dimensions for Class 300 and up.

The butt weld is easier to inspect non destructively than the fillet welds.