clamping force的意思

clamping force中文翻譯：

[機]夾緊力；[機]鎖模力

相似詞語短語

clamping kit───n.組合壓板

clamping pex───夾緊pex

clamping square───夾緊方

clamping voltage───嵌位電壓

clamping plates───夾板

clamping down───取締；施加壓力，強行壓制

clamping ring───夾緊環；壓圈；壓圈，夾圈; 鎖環

clamping system───夾緊機構

clamping knobs───夾緊旋鈕

雙語使用場景

blasting clamping force is, the more blasting vibration is produced to the adjacent tunnel.───爆破夾制作用越大，鄰近隧道產生的爆破振動越大；

They can not tell how much the mould clamping force is on earth?───他們不能指示鎖緊力究竟是多少？

using an injection moulding machine, it is best to use the minimal but adequate clamping force f.───使用注射成型機，最好使用最小同時充足的鎖模力f。

Due to the mold's expansion when in temperature rising and its shrinkage when in temperature drop, the clamping force is quite unstable.───模具升溫時受熱膨脹，降溫時又會收縮，使鎖模力很不穩定。

The new swing clamps maintain the total clamping force by a patented self-locking device if hydraulic pressure is cut off or drops.───新的搖擺夾維持專利自鎖裝置的總鎖模力液壓如果被切斷或下降。

the improper clamping fixture material and clamping force are the main reasons for the fin bending.───夾具的材料和夾緊力的大小不合適是導致翅片彎曲倒伏的主要原因。

Clip book disk acts as a location and clamping force, compactness should be appropriate.───夾書圓盤起到定位及夾緊力作用，松緊度應適宜。

Fixture layout and clamping force are two main aspects that influence the degree and distribution of machining deformation.───夾具布局和夾緊力是兩個影響的程度和加工變形分布的主要方面。

This paper focus on simulating the KM toolholder taper interface positioning under different clamping force by using Finite-element Method.───針對KM刀柄錐面定位在不同夾緊力下進行有限元模擬，得到徑向位移、接觸應力、錐面間隙結果。

英語使用場景

The axial stress in them produces a clamping force equal to the product of the proof-load stress, reduced by a design factor, and the core area of the bolt or screw.

The mechanical system consists of moving mechanism, clamping force amplifier, rotating manipulator mechanism.

Reasonable setting combining a model parameters, low voltage protection and clamping force.

The fast and powerful clamping force, extending larger clamp area avoid damage casing.

This paper studys the mechanism of fine blanking process by matrix algebra of large de- formation and grid experiments. The experiment parameters include the clamping force and die clearance.

The new structure and main design parameters of a compound die for blanking and drawing with a constant clamping force have been presented. The die is used on a single-action mechanical press.

A high - rigidity, strong clamping force and high cost performance and other characteristics.

A modular machine tool for a minicar back bridge leads deformation of the workpiece in machining because of large clamping force.

The new swing clamps maintain the total clamping force by a patented self-locking device if hydraulic pressure is cut off or drops.