青年中文asperities的意思
asperities中文翻譯：
n.粗糙；表面微凸體；艱苦的條件（asperity的復數）
austerities───n.緊縮；樸素；苦行；嚴厲
prosperities───n.繁榮，成功
aspersories───n.灑水器（等于aspergillum）
disparities───不一致（disparity的復數）
superbities───超級咬傷
supercities───n.特大都市；人口稠密地區
amenities───n.令人愉快之事物（amenity的復數）
asperate───adj.粗糙的；vt.使粗糙
asperges───n.灑水禮；n.(Asperges)（意、法、美、比）艾史派爾杰（人名）
size of the peaks, or asperities, depends on the material and the method of surface finishing.───峰或突起的大小與材料和表面拋光方法有關。
In this paper, a three-dimensional measuring system for surface asperities is described, in which a microcomputer is interfaced to a stylus profilometer.───本文介紹采用觸針式輪廓儀與通用微型機相連的表面三維形貌測量系統。
at higher angle of tooth-shaped asperities and under higher normal stress, the failure model II is found, which is in first tension but final shear failure.───在較高的法向應力下，含起伏角較高齒形節理面的非貫通節理巖體可能出現破壞模式II（先張拉后剪切破壞模式）。
She was oppressed by an abiding sense for the asperities and inequalities of society.───她深受壓抑，長期因社會的冷酷和不公深受困擾。
Agglomerates of delusterant particles located near the surface of synthetic fibers cause asperities .───消光劑顆粒集結在合成纖維表面附近，導致表面粗糙。
This, acting on the spongy weakened asperities, will allow the surfaces to interact with minimal damage.───這層東西作用在松軟的微凸體上，將使相互作用表面的損壞危險減至最小。
The rough profile of the joint suface is modeled as a series of irregular shaped, triangular asperities.───典型節理面的粗糙形貌可以模擬為一系列非規則的、齒形凸臺形貌。
If the gouge layer is thin, contact between asperities on the rock surfaces can occur.───如果充填物層很薄，兩個巖石表面上的凸起物就有可能互相接觸。
The running-in period for various machines and engines produces this type of wear by removing the peaks from asperities(fig. 16. 3).───在磨合期，各種機器及發動機通過粗暴的接觸而磨掉表面的波峰等產生此種磨損（圖16.3）。
Merchant thought that minute asperities existed at the chip-tool interface and the fluid was drawn into the interface by the capillary action of the interlocking network of these surface asperities.
The influences of the steady-state frictional heat on the contact performance of surface asperities and subsurface stress distribution in contact bodies were investigated.
If the gouge layer is thin, contact between asperities on the rock surfaces can occur.
In this paper, a three-dimensional measuring system for surface asperities is described, in which a microcomputer is interfaced to a stylus profilometer.
When under the same axle load, if the wheel rolling speed gets higher, the adhesion coefficient declines as the ratio of the mean asperities contact pressure to the total pressure becomes smaller.
It is noted that there is a thin fluid film between the loaded asperities and the wafer being polished in CMP process, thereby a flow system with nano scale film is formed in.
The results demonstrate that when surface roughness increases, the load capacity and the frictional force of surface asperities increase, but the oil film-thickness ratio decreases.