dip angle的意思

dip angle中文翻譯：

[力]傾角；俯角；[地物]磁傾角

相似詞語短語

dip───v.浸，蘸；（使）下降，下沉，減少；（把手、工具）伸入（袋子、容器）；扒竊；動用（資金）；瀏覽（書籍）；（給牲畜）洗藥浴；制作（蠟燭）；給某人施洗禮；（道路、地面）向下傾斜；放下，下移；（把汽車前燈）調為近光；n.(Dip)（阿根廷、印、美）迪普（人名）；n.浸，蘸；短暫的水浴或游泳；（暫時的）減少，下降；調味醬，蘸醬；凹陷處，低洼處；瀏覽，翻閱；藥浴液；舀取的量；（上坡前的）短暫下坡，（上升前的）短暫下落；傾角，視傾斜；扒手

syn dip───同步傾角

cheese dip───奶酪蘸醬

dip dye───[紡]浸染

angle───n.角，角度；視角；立場；角鐵；（古）魚鉤；v.斜移；從……角度提供信息；釣魚；謀取

dip in───浸泡；將（某物）在液體中浸一下; 分享

dip out───汲取；（澳，非正式）失敗

spinach dip───菠菜蘸醬

l dip───l傾斜

雙語使用場景

If both limbs of overturned fold have same dip Angle we call this special overturned fold isoclinal fold.───如果倒轉褶皺構造的兩翼傾角相等，則可稱這種特殊類型的倒轉褶皺為等斜褶皺。

From the model, the effects of the dip Angle and feed rate on thrust force are estimated.───在此基礎上，分析比較了進給量、斜面傾角等參數對斜面鉆孔初期受力的影響。

All planar structures are represented by a strike line and dip Angle.───一切面狀構造均可用向線和傾斜角來表示。

Forming of the force of center uplifting and lateral compressing depends on the size of dip angle of plate subduction.───中央隆升力和側向擠壓力的形成取決于板塊俯沖傾角的大小。

This paper recommend a royal road about dip angle and tendency of the tunnel roof and analysed the applicability .───介紹了一種測算巷道頂板真傾向、真傾角的快捷方法，分析了優缺點和適用條件。

The plane dips to the south with a dip Angle of fifty-five degrees.───傾斜斷面傾向南，傾角55度。

When the hydraulic support dip angle is bigger, it must consider antislipery and guard against the inverted problem.───液壓支架傾角較大時，必須考慮防滑與防倒的問題。

One limb dips to the north with a dip angle of 46 degrees and the other limb dips to the south with a dip angle of 48 degrees.───其中一個翼傾向北，傾角46度，另一個翼傾向南，傾角48度。

英語使用場景

The controlling acton of stratigraphical dip angle on layer-sliding intensity in folding process is explained systematically.

In the typical geological researches, the attitude of rock formation is characterized by using its strike angle, dip direction angle and dip angle.

The deflectometer described in this paper is used to locate drilling and determine the dip angle of boreholes.

The classic theoretical solution of the force for the plastic deformation of one end of round bar between the dies with dip angle has not been known up to the present.

All planar structures are represented by a strike line and dip angle.

Relationship curves between seam dip angle, horizontal section height and roof deformation are derived, at the seam time, the criterion of failure is given in this paper.

The pipe is damaged more seriously when the dip angle of the reverse fault is large.

When the dip angle is shallow a reverse fault is often described as a thrust fault.

This article described the developing condition of high dip angle belt conveyor and the double belt direction-support-pocket conveyor.