extrusion process的意思

extrusion process中文翻譯：

擠壓過程；壓鑄工藝

相似詞語短語

extrusion online───擠出聯機

joggled extrusion───點動擠壓

extrusion companies───擠壓公司

extrusion thermoforming───擠壓熱成型

extrusion gis───擠壓地理信息系統

extrusion reflex───擠壓反射

process───n.（為達到某一目標的）過程；（自然變化的）過程；工藝流程；訴訟程序；傳票；突起；進展；（發型）直發式；v.加工；審核；處理（數據）；列隊行進；沖印（照片）；把（頭發）弄成直發；adj.經過特殊加工的；照相板的；染印法的

boltrope track extrusion───螺栓繩軌道擠壓

probate process───遺囑認證程序

雙語使用場景

practical calculations are made according to extrusion process parameters and some technology data.───擠壓工藝參數及有關技術數據進行了實際計算。

twin screw reactive extrusion process for nylon 6 inland was introduced.───介紹了國內尼龍6的雙螺桿反應擠出工藝。

This is what happens when polyethylene molecules come through a die at the end of an extrusion process.───這就是當聚乙烯分子在擠壓最后過程通過模具時發生的情況。

The results show that the extrusion process with the disc can basically solve the question of aggradation-caboodle.───結果表明，漏盤反擠工藝能基本解決沉積堆的問題。

An analysis on the cold extrusion process and a technological experiment were made for the two spline ends of a slim drive shaft .───細長傳動軸兩端花鍵頭進行了冷擠壓加工分析與工藝實驗。

Therefore, whenever the extrusion process of coordination of the production line balance, you've got to continually turning as a long time.───所以，每當擠出工藝生產線達到平衡協調狀態后，就得讓它連續不停地運轉盡可能長的時間。

The defect of extrudate in the extrusion process in the form of melt fracture could only be evidenced in the semisolid state of PP melt.───在擠出過程中，以熔體破裂形式出現的擠出物的缺陷只有在PP熔體處于半固體狀態時才能觀察到。

The knowledge representation methods and fuzzy reasoning mechanism of a cold extrusion process planning system were researched.───研究了冷擠壓工藝設計領域的知識表示以及冷擠壓工藝設計系統的模糊推理機制。

The upsetting process step was arranged: the current pre-forming process was modified to be half-closed extrusion process.───設置鐓粗工序，將現有的開式預鍛工藝改進為半封閉式的擠壓工藝。

英語使用場景

The non - mandrel roll extrusion process of shaped tube was simulated using nonlinear FEM software.

This paper introduced the knowledge based system framework of multistage cold extrusion process planning.

Nozzle. Canula , and orifice features may be varied to suit particular requirements, provided these are within the practicabilities of the impact extrusion process on a mass-production basis.

This paper introduces the method that applies the code knowledge into cold extrusion process planning and transforms the information into feature code for the parts.

The cold extrusion process and mould design have been introduced of the pressing drill sleeve.

The distinguishing feature of continuous extrusion process is that the pressure which is needed for extrusion comes from a rotary friction wheel.

Many factors affecting cell nucleation and cell growth among the extrusion process such as preshaping pressure, melt temperature, melt viscosity, interfacial tension, take-up speed and the te.

Continuously improve the extrusion process capability with quality team.

The defect of extrudate in the extrusion process in the form of melt fracture could only be evidenced in the semisolid state of PP melt.