filling process的意思

filling process中文翻譯：

填土工作

填充過程

相似詞語短語

filling───n.(Filling)人名；(瑞典)菲林；n.填充；填料；v.填滿；遍及（fill的ing形式）

filling machine───灌裝機；[食品]充填機；銼鋸機；裝料機; 灌注機器; 充填機械; 加料機

filling stations───汽車加油站（等于gasstation）

filling into───填充

filling up───填補；裝滿；堵塞；[機] 埋乞法; 裝滿

dental filling───補牙

filling date───交發日期；申請日；交發日期，填寫日期

fuel filling───加油；加注燃油；填充燃料

filling pieces───填充件

雙語使用場景

The final step of the filling process is to use acrylic glazing compound to fill minor surface flaws.───最后的步驟用丙烯酸釉填充表面的裂縫。

You must know how to stop the cylinder-filling process in case of an emergency.───你必須清楚在緊急的情況下如何停止氣瓶的充裝。

You must know how to stop the cylinder filling process in case of an emergency.───你必須知道在緊急情況下，如何停止氣瓶的充裝。

To be used cans have to be completely sealed with automatic sterilization. Foreign matters cannot pollute during tank filling process.───使用的罐裝設備是全封閉自動殺菌的，罐裝過程中異物不可能污染。

A threedimensional mathematical model of the resin transfer molding(RTM) filling process for the automobile bumper was presented.───首先建立了汽車保險杠樹脂傳遞模塑充模過程的三維數學模型；

The filling process, solidification process and air entrapment condition of the aluminum casting were shown by numerical simulation.───通過數值模擬的方法對該鑄件的充型過程、凝固過程及鑄件的氣體卷入情況進行模擬。

A low viscosity fluid without chemical reaction was used in this study to simulate the mold filling process in cold state during RIM.───本文采用無化學反應的低粘度流體進行RIM充模過程的冷態模擬研究。

Actually this pre-formed pouch has got its final volume before filling and will not not be deformed during filling process.───其實這預成型袋已得到填補之前的最后一卷，也不會不灌裝過程中變形。

Documented skill prerequisites for filling process roles and responsibilities, and evidence that assigned staff meet these criteria.───為安排執行過程的角色和職責而文檔化的技能先決條件，并且根據這些文檔來分派人員看到這些標準。

英語使用場景

The origination and location of shrinkage porosity(hole)in the rudder horn was described by simulating the filling process of large pelagic cast-steel rudder horn using a CAE software.

Computer simulation was employed to optimize filling system to predict filling process and prevent the defects for Al alloy automotive parts in semi-solid die casting.

The molding filling process is a very important phase in RTM.

The filling process, microstructure and mechanical properties of A 357 alloy was studied by low pressure casting.

According to the force analysis of seeds during filling process, the calculation formulas for ultimate filling angle and falling angle of seed on scoop side were established.

Numerical simulation technology has been carried out to analyze the filling process of an aluminum alloy wheel produced by low pressure die casting.

Result shows that sediments transportation and filling process is controlled by fault terrace zone and accommodation zone formed by the major fault in structural transfer zone.

The filling process of the 12150 V diesel engine block casting was studied using finite element.

The effect mechanism of vacuum on the filling process was discussed. It shows that the vacuum can reduce the gas counterpressure in the casting mould cavity and improve the filling ability.