青年中文青年中文

finishing cut的意思

finishing cut中文翻譯:

精加工

相似詞語短語

finishing───v.完成;結束;(競賽)獲得(名次);用完,吃光(finish的現在分詞);n.得分的表現和技巧;(非正式)最后的修整

finishing touches───n.最后潤色; 收尾工作;n.最后潤色;收尾工作

finishing touch───最后一觸,最后一筆;最后潤色

finishing line───(賽跑的)終點線;n.精整作業線,終點線

cut cut───切,切

finishing nails───精整釘子

finishing lines───終點線,終航線;n.精整作業線,終點線( finishing line的名詞復數 )

surface finishing───表面精加工,表面修整

cut───v.割破;(用刀等)切下,割成;剪短;釋放;剪裁;削減;刪節;剪切;停止做;斷絕(關系);剪輯;切換畫面;曠(課);傷害;切牌;相交;劈出(通道);錄制(音響);adj.縮減的;割下的;雕過的;n.切,割;傷口;開口;削減;理發;(服裝等的)式樣;(錢的)份額;刪節;割下的肉;傷害的話(或行為);(場景)切換;(比賽)半程;切球;樂曲;剪輯;河道

雙語使用場景

new WEDM (Wire Electrical Discharge Machining) technology for finishing cut has been developed, in which gas has been used as a dielectric instead of water.───用氣體介質代替液體介質,開發出了一種新型的電火花切割精加工工藝。

There are two kinds of cuts in machine- shop work called, respectively, the "roughing cut" and the "finishing cut".───機械工廠的切削加工有兩種,分別稱為“粗切削”和“精切削”。

Generally speaking, bars of steel, forging, castings, etc. are machined to the required shape and size with only one roughing and one finishing cut.───一般地說,鋼質棒料、鍛件、鑄件等只經一次粗切削和一次精切削即可達到所要求的形狀和尺寸。

A roughing cut is usually to be followed by a finishing cut .───粗切削之后通常要精切削

the finishing cut , to make the work smooth and accurate , is a finer cut.───精切削是使工件表面光滑、尺寸準確,因而是一種更精細的切削。

Numerical simulation of surrounding rock stability of finishing cut in fully mechanized top coal caving───綜放收尾切眼圍巖穩定性數值模擬

Stability Analysis and Support Study on Surroundings of Finishing Cut───收作眼圍巖穩定性分析與支護技術研究

A Method of finishing cut in deeply inclined caving face with single hydraulic props───大傾角放頂煤單體面收作方法新探

Finishing Cut Method of End-mining in Plow Mining Face───刨煤機工作面末采收尾方法

英語使用場景

Generally speaking, bars of steel, forging, castings, etc. are machined to the required shape and size with only one roughing and one finishing cut.

A new WEDM(Wire Electrical Discharge Machining) technology for finishing cut has been developed, in which gas has been used as a dielectric instead of water.

By means of finishing cut the trackless rubber-tried vehicle can directly go to the working face to remove the equipment.

Also, in some jobs, fot example, when great accuracy is not needed, or when a comparatively small amount of metal must be removed, a finishing cut may be all that is required.

The stability of the surrounding rock masses of finishing cut is analyzed systemically and its support design is optimized by numerical simulation with RFPA2D.

The removal speed of the fully-mechanized coal face with topped caving (FCFTC) can be increased by pre-excavating finishing cut on terminal mining line.

Because the finishing cut is continuously affected by the abutment pressure in front of the face, its maintenance is much more difficult than that of the ordinary coal entry.

There are two kinds of cuts in machine- shop work called, respectively, the "roughing cut" and the "finishing cut".