bending stress的意思

bending stress中文翻譯：

彎曲應力

相似詞語短語

bending───n.彎曲，彎曲度；v.彎曲（bend的現在分詞）

stress───n.壓力；強調；緊張；重要性；重讀；vt.強調；使緊張；加壓力于；用重音讀；n.(Stress)人名；(意)斯特雷斯

flatwise bending───平面彎曲

bending over───俯身；折轉

flexural bending───塑性彎曲

anticlastic bending───抗塑性彎曲

bending moment───[力]彎矩；[力]彎曲力矩；[力]撓矩；彎（曲）矩，撓矩

alternating stress mean stress───交變應力平均應力

shear stress───[力]剪應力；[力]剪切應力；剪應力; 切變應力; 切應力; 粘性摩擦應力

雙語使用場景

It can provide the strip with longitudinal tensile stress and transverse bending stress.───它可使被矯帶材產生縱向拉伸應力和橫向彎曲應力。

Thus the bending stress is very easily computed.───因此，極容易計算出其彎曲應力。

Avoid excessive bending stress by a pulley.───應安裝滾輪避免過度彎曲。

Within reasonable limits, the presence of the shearing stress has no effect on the value of the bending stress, and vice versa.───在適當的限度內，剪應力的存在并不影響彎曲應力之值，反之亦然。

Fatigue cracking of a roller is the main failure form due to the alternate bending stress in operation.───滾圈是回轉窯最重要的支承部件，運轉中彎曲應力造成的疲勞開裂是其主要失效形式。

I have no idea of their having found a better drill bending stress.───我沒聽說他們找到了能抵抗高彎曲應力的好鉆桿。

But the influence of the bending stress was not considered by equal-area method and the pressure area method of reinforcement.───而等面積補強法與壓力面積法均未考慮彎曲應力的影響，是不安全的。

Find the value of the bending stress and the deflection at the center if the ribs are omitted.───如果略去肋條，求中心處的彎曲應力和撓度之值。

Formulas of shearing stress and bending stress were derived, and the failure criterion was given in the paper.───推導了根茬在切割過程中受到的剪應力、彎曲應力計算公式，給出了破壞準則。

英語使用場景

Pegs have a larger core diameter and are likely to resist bending stress better than screws, however, screws may provide better grip on individual bone fragments.

Circular-arc-tooth-trace (CATT) cylinder gear differs from straight-cut cylinder gear in calculation of the gear tooth bending stress.

Curvature and bending stress amplitude of double helix in langs of wire rope are much larger than in ordinary lay.

The bending stress varies axially while the average axial stress changes a little.

Axial force has a great effect on deformation of rod or tubing with initial bending stress.

The arithmetic for bending stress of DIGLST is presented after the coefficients of helix angle and contact lines are analyzed by 3-D FEM.

Elementary Elastic Bending theory requires that bending stress varies linearly with distance from the neutral axis, but plastic bending shows a more accurate and complex stress distribution.

Therefore, the BP network model can be used directly in the tooth root bending stress calculation, especially for gear tooth root bending stress calculations of high-precision.

In frequent bending stress condition, fatigue cracking occurred due to the cracking source had been initiated in welding heat affected zone.