injection pressure的意思

injection pressure中文翻譯：

[塑料]注射壓力，噴注壓力

相似詞語短語

pressure───vt.迫使；密封；使……增壓；n.壓力；壓迫，[物]壓強

alegar injection───阿萊加注射液

amnios injection───羊膜注射

cash injection───資金注入

direct injection───直接射油，直接注入；[動力]直接噴射；直接注入；直接射出法

corticosteroid injection───皮質類固醇注射

dependency injection───依賴注入

injection mold───[塑料]注塑模具

administering injection───注射給藥

雙語使用場景

Cycle polymer flooding method can reduce injection pressure.───周期注聚方式可以降低注入壓力。

Influence of injection pressure and fuel temperature for standard fuel consumption was studied.───了噴油器開啟壓力和試驗油溫度對標準油量的影響；

Injection pressure in one of the major factors effecting the results of development of sandstone reservoirs.───注水開發的砂巖油田，注水壓力的高低對油田開發效果有很大的影響。

In the function of injection pressure, the mould which has core will produce a little core offset and cause plastics deformation.───具有型芯的模具，在注射壓力的作用下，將使型芯產生一定偏移，引起塑件變形。

When the close time of the nozzles was set at the end of packing, the injection pressure, clamp force and parts quality were all better.───同時當澆口均設置為保壓結束時關閉，成型中的注射壓力、鎖模力以及制件質量較為理想。

The injection pressure is commonly described as the surface pump pressure required to achieve injection.───注入壓力普遍地是指實現注入所需的地面泵壓。

Bad injected water quality have damaged formations and made injection pressure step up in Shasanzhong 6-10 low permeable reservoirs.───濮城油田沙三中6-10油藏為低滲油藏，因注入水質差，造成對地層的傷害，注水壓力不斷上升。

Theoretical result shows that even in a very low admixture injection pressure, fracturing will occur in surrounding soil.───理論分析發現即使在很小的固化劑注入壓力作用下，周圍土體也會發生劈裂現象。

The high pertinence between the weight of injection molding products and injection pressure is unveiled by experiments and analyses.───通過實驗和分析揭示了注塑機產品的件重和充填過程的壓力之間有很強的相關性。

英語使用場景

Electric unit pump system is a new type fuel injection system with high injection pressure which can be applied to control fuel quantity and timing of injecting flexibly.

Due to high injection pressure of high concentration polymer solution, reducing injection pressure of high-concentration polymer solution with surfactant has been researched.

The molder must recognize the dangers of excessive fill speed, insufficient injection pressure, excessive melt temperature, and inadequate packing.

The sensitivity analysis indicates that the parameters impacting the production results from high to low are production time, steam dryness, cyclic steam injection volume, steam injection pressure.

During the process of water injection production, high injection pressure cut in mudstone should be prevented to reduce casing damage.

Water injection efficiency depends on whether the injection pressure is high or low in water injection wells.

It is demonstrated that a flashing jet is worn away into a cone shape and the jet extinct length decreases with the increasing of pressure decay ratio of injection pressure to backpressure.

Therefore, using higher specific gravity and dynamic viscosity of biodiesel is able to decrease fuel injection pressure properly.

It could non-disassembly dynamic test several parameters of the fuel system, such as fuel injection pressure, fuel injection bulkhead angle, fuel injection and fuel supply advance angle.