青年中文serration的意思
serration中文翻譯：
n.（行掃描起點不一致引起屏幕上的）鋸齒狀；鋸齒狀突起（等于serrature）
serrate gene───鋸齒基因
chloranthus serratus───[醫] 及己
prunus serrulata───櫻桃
serrated edge───牙子；鋸齒形邊
shea serrano───謝·塞拉諾
serrate verb───鋸齒狀動詞
serrasalmus geryi───謝爾拉薩爾穆斯格伊
serranus cjer───蛇
serrate suture───[解剖]鋸狀縫
serrate leaf───鋸齒葉
The results show that high stress in serration and its arc transition region, and observed that severe stress concentration in these locations.───結果表明葉片高應力區域位于榫齒及其圓弧過渡處，并且發現在這些位置存在嚴重的應力集中情況。
points for attention in designing the serration axle are pointed out.───指出了漸開線螺旋花鍵軸幾何尺寸設計時應注意的問題。
The new method for designing Fresnel lens has a wide serration breadth and unequal pitch.───用這一方法設計的菲涅耳透鏡，齒寬較大，齒距不等。
Point contact in both cylinders Small grooves are called "Serration" , each serration assign as cutting edges.───小槽被稱為“鋸齒”每一鋸齒可看作為一個刀刃。
screw driver for screws with internal serration - screw driver points , gauges and test specimens for torque testing.───螺釘和螺母的裝配工具。十字頭套筒扳手。尺寸和扭矩試驗。
Post processing method is put forward in order to removal serration of spectral curve after calibration.───提出了反射率反演后波譜曲線上存在的鋸齒狀現象的消除方法；
secondary veins 13-15 on each side of midvein, adaxially slightly raised, fusing at serration.───中脈凹陷次脈13-15在中脈兩邊各，正面稍突起，在熔化。
Serration flow phenomenon of aluminum alloy used for can body stock───易拉罐用鋁材的鋸齒屈服現象
Mechanical Analysis of Crack Failures in Turbine Blade and Disk Serration of an Aeroengine───某型航空發動機渦輪葉片和輪盤榫齒裂紋故障力學分析
As the rise of the strain rate, the feature of the true stress- true strain curve changed from "flat" to "serration", and the thermal deformation softening feature was reinforced.
The full text used the methods of combining literature and the literature, and make serration research as a whole for Li zhi.
The results show that high stress in serration and its arc transition region, and observed that severe stress concentration in these locations.
Unless otherwise specified, the nozzle gasket surface shall be flat smooth surface and serration specified in ANSI standard is not to provide.
It is difficult to grind bore on gear and secure its precision. Especially more linkage gear's precision can not be secured easily, so it maybe become a waste product because of serration error.
We adopt serration design in order for thermolysis and life.
The optimization rule on the layout and serration of the compact range was referred to, then the optimization algorithm was performed and the result was given.
Moreover, intergranular corrosion on the serration surface is other reason to induce GH2036 turbine disc to early fail under the high-temperature combustion condition.
The points for attention in designing the serration axle are pointed out.