mass flow rate的意思

mass flow rate中文翻譯：

[流]質量流率

相似詞語短語

flow rate───流量; 流率；[流][水文]流量；[流]流速

volumetric flow rate───體積臨；[流]容積流率

proportional to flow rate───與流量成比例

flow───vi.流; 垂; 流出; （談話、文體等）流暢；n.流動；生產，供應；車流；流量；傳播；流通；滔滔不絕；連貫，流暢；漲潮；泛濫；（蘇格蘭）濕地，沼澤；月經；vt.使泛濫; 淹沒; 排出；n.流動; 滔滔不絕; 漲潮; 連貫；v.（使）流動，涌流；流通；傳播；流暢；充滿；大量供應；漲；漲潮；川流不息；飄揚；來自，由……產生；來月經；（礦物、巖石等）變形；n.(Flow)（美）弗洛（人名）

rate───n.(Rate)人名；(法、塞)拉特；n.比率，率；速度；價格；等級；vi.責罵；被評價；vt.認為；估價；責罵

mass───n.塊，團；群眾，民眾；大量，眾多；質量；vt.使集合；adj.群眾的，民眾的；大規模的，集中的；vi.聚集起來，聚集

ceaseless flow───源源不斷的流動

cohesive flow───粘性流

flow controller───[自]流量控制器

雙語使用場景

Experiments were carried out to the research on mass flow rate measurement using vortex flowmeter.───利用差壓原理進行質量流量測量的方法進行實驗研究。

With increase of mass flow rate, solid-gas ratio increases first and then decreases.───隨著煤粉的輸送流量的增大，固氣比先增大后減小。

The numerical results comprehensively describe the influence of the slip boundary condition on mass flow rate.───數值分析結果給出了速度滑移邊界條件對管道質量流量的影響。

The mass flow rate of the molten metal is controlled by means of a choke element fitted in the casting trough.───熔融金屬的質量流率借助配合在澆注槽內的一個扼流元件控制。

Experimental results manifest that this method is feasible and effective for mass flow rate measurement.───結果表明，該測量方法結構簡單，是測量質量流量的有效方法。

However, the rate of decrease in cooling water exit temperature decreases with an increase in air mass flow rate and spray water rate.───隨著空氣質量流量和噴淋水量的增加，冷卻水出口溫度降低，但是變化斜率逐漸減小，即存在著一最佳噴淋水童和空氣質量。

However, in this case it is easier to use a mass flow rate because referring to a hippo feed rate in terms of moles is impractical.───然而，在這種情況下這是更容易使用一個質量流率，因為指從河馬喂入痣的不切合實際。

The results show that the system runs steadily when the driving flow mass flow rate equals to the diffuser outlet vapor flow mass flow rate.───結果表明，當工作流流量同擴壓段出口蒸氣流量相等時系統能夠穩定運行。

Also, note that the mass flow rate value is recalculated from the velocity or volume flow rate value specified on an opening.───同時，注意到率值從在一開放上指定的速度或者量流量值被重新計算的大規模的流動。

英語使用場景

Mass flow rate of added fuel, injecting location and physical throat area on rocket ejector performance were investigated.

Higher heat transfer rate as air mass flow rate increases.

The effects of the packing factor, working fluid mass flow rate on the thermal efficiency and electric gain were investigated, and the optimization of design parameters have been found in this paper.

The mass flow rate varies with the inner diameter and the length of adiabatic capillary tubes, the degree of subcooling and the condensing temperature were investigated.

Adiabatic combustion temperature at various oxidizer mass flow rates and grain length is obtained by thermodynamic calculation and has a maximum as oxidizer mass flow rate increases .

The relation between mass flow deviation and setting angle, flow pattern, liquid apparent mass flow rate is analyze based on the theory of two-phase flow.

The capillary tube model in subcooling single-phase region and two-phase region was established, and the difference of mass flow rate is within 10% between the predicted and the measured values.

The control properties of vortex valve for mass flow rate are numerically simulated.

With increase of mass flow rate, solid - gas ratio increases first and then decreases.