metal flow的意思

metal flow中文翻譯：

[機]金屬流動

相似詞語短語

flow───vi.流; 垂; 流出; （談話、文體等）流暢；n.流動；生產，供應；車流；流量；傳播；流通；滔滔不絕；連貫，流暢；漲潮；泛濫；（蘇格蘭）濕地，沼澤；月經；vt.使泛濫; 淹沒; 排出；n.流動; 滔滔不絕; 漲潮; 連貫；v.（使）流動，涌流；流通；傳播；流暢；充滿；大量供應；漲；漲潮；川流不息；飄揚；來自，由……產生；來月經；（礦物、巖石等）變形；n.(Flow)（美）弗洛（人名）

metal───vt.以金屬覆蓋；n.（Metal）（捷、瑞典）梅塔爾（人名）；n.金屬；合金；adj.金屬制的

ceaseless flow───源源不斷的流動

cohesive flow───粘性流

flow controller───[自]流量控制器

current flow───電流

flow about───流動

flow production───流水線生產；大規模生產

flow diagram───n.流程圖，作業圖，生產過程圖解; 框圖；[工業]流程圖；作業圖

雙語使用場景

The results indicate that the metal flow curve wavily fluctuates.───結果表明，金屬流動曲線起伏很大。

And calculate the equation in compensation amount of probing into the metal flow of more detailed description.───并較詳細的描述探討了金屬流量的補償量計算方程。

and metal flow in steel tube during sizing process were analyzed.───分析了定徑過程中鋼管內金屬流動和彈復行為。

Coining is usually done on surfaces parallel to the parting line, and little metal flow is involved in the operation.───鑄幣通常是做表面平行的線，與小金屬流動是參與行動的。

Metal flow of lead screw cold roll-beating process is analyzed, and metal flow's law of minimum resistance is verified.───分析了絲杠冷滾打過程中金屬的流向，驗證了金屬流動最小阻力定律。

This flexibility accommodates any process, maintenance, or emergency metal flow direction to be achieved.───這樣的靈活性使得任何過程，維護或緊急狀態下的金屬流動方向都能夠達到。

Through the simulation, the rules of velocity field deformation area distribution and metal flow have been obtained.───通過三維有限元模擬輾環軋制過程，得到了軋制過程中的變形區速度場分布以及金屬流動規律；

The investigation showed that metal flow during the upsetting is different from continuous motion of deformation units fined by finite . . .───試驗證明，在鐓粗過程中金屬的流動并不是有限元解出的變形單元的連續移動。

Metal flow takes place within the plastic range of the metal, so that the bend retains a permanent set after removal of the applied stress.───金屬的流動發生在金屬的塑性變形范圍之內，因此在施加的外力去除之后彎曲保持永久的變形。

英語使用場景

During the friction stir welding process of aluminium alloy, the plastic metal flow in the weld is a kind of single-phase flow.

The experiments show that using UBET to Simulate the laws of the metal flow in drop forging was available.

The metal flow during indirect extrusion is analyzed, and the influence of billet machining on the quality of aluminium tube is also investigated.

On the basis of experiment and change of metal flow line, metallographic structure and micro-hardness in deformation zone, this paper researched process, characteristic and mechanism of fine-blanking.

The air entrapment of the liquid metal flow in the shot sleeve during the slow shot phase is one of the factors resulting in this kind of defect.

The liquid metal flow during mould filling in bottom gating system and its influence on the casting quality are introduced emphatically .

The results show that both gas-forming property and decomposition latent heat of the polystyrene material influence the metal flow velocity and the gaseous pressure of the gap significantly.

Compared with raw material, the cup formed by the technology of warm forming has perfect metal flow lines and the body's hardness and tensile strength are g...

For the defects such as dead zone and shrinkage cavity in conventional extrusion process, an inner cone punch was proposed to improve the metal flow behavior.