mold wall的意思

mold wall中文翻譯：

模具壁

相似詞語短語

mold───n.(Mold)（美、英、奧地利）莫爾德（人名）；n.模具；鑄模；模制品；類型，個性，風格；框架；體型，模樣；霉，霉菌；耕作土壤；松軟沃土；v.澆鑄，塑造；用模子制作；對……影響重大；將……塑造成；使）緊貼于，吻合；輪廓相符；使發霉

mold removed───脫模

botchy mold───爛霉

wall to wall───遍地皆是

button mold───n.包鈕

mold tech───模具技術

triturate mold───研磨模具

figurine mold───塑模

detecting mold───檢測模具

雙語使用場景

New residential living large mold wall, floor played drums mold phenomenon.───新建住宅墻體出現大量的霉斑，地板起鼓發霉等現象。

technology of vibratory sink mold wall, the layering characteristic of the preventing seepage material of the composite mortar is studied by the layering vibratory dais model test.───振動沉模防滲墻技術，通過分層模型的振動臺試驗，研究了混合砂漿防滲料的分層性隨振動模型的變化情況，揭示了混合砂漿防滲料的性能指標隨振動模型的變化規律。

According to the technology of vibratory sink mold wall, layering characteristic of the preventing seepage material of the composite mortar is studied through the layering vibratory dais model test.───結合振動沉模防滲墻技術，通過分層模型的振動臺試驗，研究了混合砂漿防滲料的分層性隨振動模型的變化情況，揭示了混合砂漿防滲料的性能指標隨振動模型的變化規律。

in the mold with a brush in the cake flour, cake flour to stick to the mold wall evenly, then pour out the excess flour cake.───在模具里用刷子刷上糕粉，讓糕粉均勻粘在模具壁上，然后把多余的糕粉倒出來。

the film totally eliminated after washing wiping syrup used to kill mold wall, after dry brushing.───電影完全消除后，抹用來殺害模具壁藥水清洗，干燥后刷牙。

The measured results indicated that the mold wall temperature approaches the temperature of cooling water.───實驗結果表明，結晶器內壁溫度趨近于冷卻水溫度。

The preparation technique for cobaltous aluminate, the coating process on mold wall and casting process are also introduced.───介紹鋁酸鈷的制備、面層涂料的配制以及合金的澆注工藝。

This advantage can reduce the mold wall movement caused by the graphitization expansion of ductile iron casting.───這一特點可以減少球鐵石墨化膨脹引起的型壁移動。

New residential living large mold wall, floor played drums mold phenomenon.───久不居住的新建住宅墻體出現大量的霉斑，地板起鼓發霉等現象。

英語使用場景

The preparation technique for cobaltous aluminate, the coating mold wall and casting process are also introduced.

This advantage can reduce the mold wall movement caused by the graphitization expansion of ductile iron casting.

The preparation technique for cobaltous aluminate, the coating process on mold wall and casting process are also introduced.