porosities的意思

porosities中文翻譯：

多孔性

相似詞語短語

medicines for osteoporosis treatment───治療骨質疏松癥的藥物

carbonation osteoporosis───碳酸性骨質疏松癥

porosity───n.有孔性，多孔性

treatments for osteoporosis───骨質疏松癥的治療

Aporosa───無瑩珊瑚部

osteoporosis prevention───骨質疏松癥預防

transient osteoporosis───[醫]一過性骨質疏松癥

bicarbonate and osteoporosis───碳酸氫鹽與骨質疏松

imporosity───n.無孔性；不透氣性

雙語使用場景

The relative amount of these two kinds of water varies greatly from one kind of rock or sediment to another, even though their porosities may be the same.───這兩種水的相對含量在不同的巖石或沉積物之間差異很大，盡管它們的孔隙率可能是相同的。

The unhealed porosities might be a possible source of flake formation.───這種空隙很可能是白點斷口的一種斷裂源。

It is well known that bed porosities are greater near the bounding surface.───眾所周知，靠近邊界表面的床層自由空間率較大。

Then the surfactant removal leads to materials of organized cage-like pore structure and tailored porosities and of large surface areas.───除去模板劑后便可以得到高比表面積、可調的孔隙率的籠型孔道結構薄膜材料。

The required porosities for various cases were obtained through varying the diameter of holes and spacing among the holes.───各物理模型通過改變氣膜孔徑大小和孔間距得到不同的孔陣排列疏密度。

No effects of thickness of the samples on the porosities and ablative properties of the composites can be observed.───制件厚度幾乎不影響復合材料的孔隙率和燒蝕性能；

What is more, asteroid porosities may have been even greater immediately after they accreted from the debris of the early solar system.───更重要的是，小行星在剛由早期太陽系里的碎片聚合而成時，孔隙率可能更大。

Each formation will create different effects on the wellbore due to the paraffin content, depth and formation porosities.───由于石蠟含量，井深和地層孔隙度的不同每個地層都會對井筒產生不同的影響。

Porosities of composites decrease with the increase of fibre volume fraction, whereas the mechanical properties increased.───隨纖維體積含量增加，復合材料的孔隙率降低、力學性能提高；

英語使用場景

The unhealed porosities might be a possible source of flake formation.

Unhealed porosities and free surface of dendrites with crystalline steps were occasionally observed in aluminium alloy forgings.

The volume density, open porosities and flexure strength of porous silicon nitride ceramics are measured respectively by Archimedes and three-point bending methods.

The reasons of porosities production and process instability in CO2 laser welding shipbuilding T-section aluminum alloy are also discussed.

The results show that a more uniform microstructure and higher hardness were obtained in the ceramal layer, and there are no porosities and cracks in it.

In the lignite matrix , the porosities are mainly and macroporosities.

In the neighbourhood of the unhealed porosities the alloy matrix appeared to be embrittled and in certain cases cleavage fracture was observed.

The reason of the formation of gas porosities and cracks on the head face of valve tappet has been studied.