side cutting的意思

side cutting中文翻譯：

[鐵路][水利]邊坡挖土

相似詞語短語

cutting───adj.尖酸刻薄的；嚴寒的，刺骨的；鋒利的；v.切割；鑿成；剪短；把……切碎；劃破（cut的現在分詞）；n.剪報；插枝，插條；狹窄通道，路塹；切割，切斷；割下的東西；n.（Cutting）（美、澳、印）卡廷（人名）

cutting line───切割線；截線

cutting down───研磨修整；磨掉

cutting shapes───切割形狀

cutting board───n.切肉板

side to side───從一邊到另一邊；邊對邊

cutting machine───切削機，[機]切割機；裁切機，裁剪機；截煤機；下料壓力機；切削機; 下料壓力機; 裁剪機; 裁切機

cutting paper───剪紙；裁紙

side in side───并排

雙語使用場景

In general the major roll forging processes consisted of blanking, heating, roll forming, locally sizing, side cutting, bending and integrally hot correcting.───主要工藝流程為：下料、加熱、成型輥銀、局部整形、切邊、彎曲、整體熱校正。

facilities for side cutting tests and some test results are introduced.───側向切削的實驗設備和一些試驗結果。

Cutting the cone at various angles gives you various shapes of ellipse. Until the angle of your cut exceeds the angle of the side of the cone.───不同角度切割圓錐，你便會得到不同的橢圓，直到你的切割角度超過圓錐體側邊的角度。

Chief engineer: Chief Officer has looked up. Look: non-spark side cutting pliers-; screw plate-; adjustable wrenches .───輪機長：大副已經查到了。看，銅老虎鉗；組合螺絲刀；活搬手。

The second one was to play line, is a book block and cover with good, then by a three-side cutting into light book hit four or six eyes.───第二次是打線眼，是書芯與封面配好，并粘牢，再經三面裁切成光本書后，打四個或六個眼。

PLIERS AND NIPPERS. LEVER ASSISTED SIDE CUTTING, END CUTTING AND DIAGONAL CUTTING NIPPERS.───夾扭鉗和彎切鉗.側切鉗

Pliers and nippers - Lever assisted side cutting pliers, end and diagonal cutting nippers - Dimensions and test values───夾扭鉗和剪扭鉗.杠桿輔助的側剪切鉗，端剪切鉗和鈄口鉗.定義和試驗值

Computer simulation for the side-cutting of roller bits───牙輪鉆頭側向切削的計算機仿真

Combination pliers with side cutting jaws transparent insulated handles, chrome plated───透明膠柄鍍鉻花腮鉗

英語使用場景

Side rake angle is the angle between the face of the tool and the base of the shank or holder and is usually measured in a plane perpendicular to the bade to the side cutting edge.

Side relief angle is the angle between the portion of the side flank immediately below the side cutting plane perpendicular to the side flank.

In this report, an overall analysis of wellbore deviation is presented. The theoretical study in side cutting mechanism and side cutting ability of cone bits are described.

The original ingate was enlarged by side cutting and roof cutting under the condition of filling behind wall by grouting, and then be supported and reinforced by the secondary support technology.