steam injection的意思

steam injection中文翻譯：

蒸汽噴射，蒸汽注入；射汽法

相似詞語短語

steam───adj.蒸汽的；n.蒸汽；蒸汽動力；水汽；精力；vi.冒水汽；蒸；用蒸汽動力推動；疾行；<非正式>開始戰斗；搶劫

alegar injection───阿萊加注射液

amnios injection───羊膜注射

cash injection───資金注入

direct injection───直接射油，直接注入；[動力]直接噴射；直接注入；直接射出法

corticosteroid injection───皮質類固醇注射

dependency injection───依賴注入

injection mold───[塑料]注塑模具

administering injection───注射給藥

雙語使用場景

Therefore, steam injection parameters for Nine-7 Block were analyzed and optimized using orthogonal experiment design.───為此，利用正交試驗設計方法對九7區注汽工藝參數進行了敏感性分析和優化。

Under the production condition of steam injection, the energy ratio can reach 7.0.───注入蒸汽開采初始條件下，能量效率可以達到7.0。

Method Steam injection development and well pattern of horizontal Wells were studied by using numerical simulation.───方法利用數值模擬方法，對水平井注蒸汽的開發、布井方式等進行研究。

Steam injection, among the oldest heat-based methods, was decisive in the revival of the Kern River Oil Field back in the early 1960s.───加熱是歷史最悠久的方法，其中蒸汽注入法是1960年代初期讓美國克恩河油田重現生機的決定性因素。

This relationship can be used to determine steam injection volume and the production distribution during steam stimulation.───利用這一線性關系，以油藏的油汽比確定注汽量，可解決稠油蒸汽吞吐階段的配產問題；

At benefit-oriented present, one of the key issues related to the cost of steam injection is the on - off of steam - water separators.───在重視效益的今天，如何對待高壓汽水分離器的關停，也是關系到注汽成本的一個關鍵問題。

The results show that high thermal stress is generated in casing at the beginning of steam injection.───分析結果表明，注汽初始階段套管內會產生較大的熱應力；

Close to end of exploiting period of heavy oil, it's usually adopting separate steam injection for enhancing oil recovery effectively.───在稠油開采的后期，為了有效提高采收率普遍采用分層注汽的生產方式。

The steam-injection boiler is the important equipment in producing viscous oil, and is the main energy consumption facility.───油田注汽鍋爐是油田稠油開采的重要設備，又是油田的主要耗能設備。

英語使用場景

The level of oil production using steam injection technique directly depends on the heat efficiency of steam injection, and the heat efficiency can be determined by injection-production parameters.

Used the hot cyclic steam injection craft mining thick oil is the thick oil development main form.

A model for optimizing the steam injection process in thermal recovery wellbore is developed and solved with enumeration method under two kinds of conditions, namely steam soak and steam flooding.

The study shows that cyclic steam injection rate, soaking time, flowing bottom hole pressure and blowdown mode are important factors influencing the effectiveness of single well steam stimulation.

The sensitivity analysis indicates that the parameters impacting the production results from high to low are production time, steam dryness, cyclic steam injection volume, steam injection pressure.

Intermittent steam injection can increase the specific volume, swept volume and utilization ratio of heat, and can improve formation of seepage in oil reservoir so as to improve flooding effect.

Major factors which influence the steam injection profile are steam overlaying and high-permeability zones during steam flooding and cyclic steam injection.

The experiment shows that nitrogen and steam injection is beneficial for increasing the effect of oil well stimulation.

The method can be used to calculate the thermodynamic properties of the moist combustion gas for any kind of hydrocarbon fuel, any steam injection ratio and any fuel coefficient.